Fenix TK20R V2.0 rechargeable light

Fenix ​​TK20R V2.0 Tactical Rechargeable Light

The Fenix ​​TK20R V2.0 tactical rechargeable flashlight offers a luminous flux of up to 3000 lumens (ANSI), charging via a modern USB-C connector and the possibility of immediate activation of the stroboscope. It is equipped with a top LED Luminus SFT-70, which in combination with a smooth reflector creates a well-focused light cone with an extraordinary afterglow of 475 meters. The package includes a Li-ion battery 21700 with a capacity of 5000 mAh, which is charged via the USB-C connector directly in the lamp. The charging hole is covered with a screw nut, so it is perfectly protected against water and dirt. The Fenix ​​TK20R V2.0 flashlight uses a dual tactical switch that enables faster and more reliable control in crisis situations. For example, it can be quickly turned on directly into stroboscopic mode. The lamp has a total of six lighting modes with a duration of up to 48 hours. Thanks to its massive design, this tactical light is strong and durable while maintaining a compact size. The robust design allows the lamp to be used on long weapons, so it is suitable for professionals, armed forces and hunting.

All lamp parameters (luminous flux, battery operation time, waterproofing, afterglow and impact resistance) are measured in accordance with the ANSI/NEMA FL 1-2009 standard.

Use of Fenix ​​TK20R V2.0 lamp

From the factory, there may be a black insulating cap inside the lamp on the battery. Remove it from the battery before first use.

To turn it on , press the larger tactical button located at the end of the lamp, for immediate activation, hold the button. By pressing the secondary toggle button, you can switch between power modes at any time during operation. To switch to flash mode (strobe) when the lamp is on, hold down the switch button for approximately 0.5 s. Press and hold the toggle button to turn the light directly into strobe mode.

Intelligent protection against overheating - due to the fact that the lamp reaches a huge output of 3000 lm, the temperature rises. If the temperature exceeds 60 °C, the power will be automatically reduced. As soon as the temperature drops below 60 °C, it is possible to use the highest power again.

Battery charge status indication - the charge indicator is hidden under the protective nut of the charging connector for tactical reasons, so it is necessary to unscrew the nut to check it. The lamp always indicates the battery charge status three seconds after switching on. Green indicates a sufficient state of charge (100% - 85%), green flashing 85% - 50%, steady red light means 50% - 25% and flashing red indicates a critically discharged battery (25% - 1%). If the battery is discharged, the lamp will gradually automatically switch to lower power modes, then in the lowest mode it will flash 3 times every five minutes.

Charging the lamp - unscrew the protective nut under the head of the lamp and use the supplied USB-C cable to connect it to a computer, USB network adapter or USB car adapter (not included in the package). Any mobile phone charger with a USB-C connector can also be used for charging. During charging, the indicator LED opposite the charging connector lights up red, after full charge it lights up green. Charging a fully discharged battery takes about 3.5 hours. The used Li-ion battery does not suffer from a memory effect, so the lamp can be recharged at any time. The lamp cannot be turned on while charging.

Accessories

• Optional accessories can be purchased: cable switch AER-05, traffic cone AOT-M, red filter AOF-M and diffuser AOD-M
• The following accessories are also compatible with the light: Fenix ​​ALD-05 helmet strap, ALG-15 quick-release weapon rail mount, ALG-00 quick-release rail mount, Fenix ​​ALG-16 M-LOK mount, Fenix ​​barrel mount ALG-18, Barrel Mount, Metal Magnetic Barrel Mount, Plastic Magnetic Barrel Mount, Optic Mount, Metal Optic Mount, FB-1 Bike Mount, Fenix ​​Bike Mount.
• The lamp can also be purchased with a USB adapter for the mains and a USB adapter for the car.

Warning

• Use only high-quality 21700 Li-ion batteries to avoid damage to the lamp, for example due to leakage of substances from the battery.
• Insert the batteries with the positive pole towards the lamp head.
• If the protective rubber rings appear damaged after a long period of use, replace them. The rings must also be lubricated to prevent rubber erosion. By following these rules, the lamp will be properly protected against water.
• If the light flickers, does not switch to higher power modes, or does not light up, it may be for one of the following reasons:
  
  • The battery is almost empty - charge it.
  • The contacts inside the lamp are dirty - clean them with a cotton swab dipped in alcohol.
  • The back part of the lamp is loose, tighten it.