Shimano Ultegra R8170 C60 28" wheelset, CL, Shimano HG, display set

WARNING
For information on installation, adjustment and replacement of the products which are not to be found in the user's manual, please consult the place of purchase or a distributor. A dealer's manual for professional and experienced bicycle mechanics is available on our website (https://si.shimano.com).
For safety, be sure to read this "user's manual" thoroughly before use, follow it for correct use, and save it for later reference.
The following directions should always be followed in order to prevent personal injury, damage to equipment or damage to the surrounding area. The directions are classified according to the degree of danger or damage which may occur if the product is used incorrectly.
DANGER – Failure to follow the directions will result in death or serious injury.
WARNING – Failure to follow the directions could result in death or serious injury.
CAUTION – Failure to follow the directions could cause personal injury or physical damage to equipment or the surrounding area.

WARNING
- Do not disassemble or modify the product. It may cause the product to not operate correctly, and you may fall unexpectedly and be seriously injured.
- Before riding the bicycle, check that the wheels are securely fastened. Improper use of the quick release lever can cause the wheel to come off, etc., and a serious injury may result from falling or colliding.
- Use the appropriate air pressure indicated on the tire and rim. If the maximum pressure is indicated on the tires or rims, do not exceed the maximum pressure with the lower value. Higher than the specified pressure may cause the tire to burst suddenly and/or the tire to come off suddenly, causing serious injury.
WH-R9270-TL / WH-R8170-TL / WH-RS710-TL: Maximum pressure = 7.5 bar / 109 psi / 750 kPa
WH-R9170-TL / WH-RS770-TL: Maximum pressure = 8 bar / 116 psi / 800 kPa
WH-RS370-TL: Maximum pressure = 6.5 bar / 94 psi / 650 kPa
WH-RX880-TL / WH-RX870-TL / WH-RX570-TL: Maximum pressure = 5 bar / 72 psi / 500 kPa
- Before riding the bicycle, check the wheels to be sure that the spokes are not bent or loose and that there are no scores, scratches or cracks on the rim surface. If any of these problems are found, do not use the wheel. The wheel may break and you may fall. Check that there is no peeling or cracking of the carbon.
- Do not use the road wheel set on unpaved surfaces. The road wheel set is designed for paved surfaces. If the wheels are used on unpaved surfaces, the wheels may bend or become damaged, and an accident may result.
- Do not use the GRAVEL wheel set in harsh conditions such as on rough roads. Do not use it for downhill riding or freeriding, otherwise the wheel may bend or otherwise be damaged if subjected to a strong impact, and an accident may result.
- Do not use with rim brakes. These wheels are designed exclusively for use with disc brakes. Using these wheels with rim brakes can damage the rims and cause an accident, which may result in serious injury or even death.
- Check that the quick release lever does not interfere with the disc brake rotor even when fully engaged. If the quick release lever is on the disc brake rotor side, it may interfere with the disc brake rotor, which is dangerous. If the quick release lever interferes with the disc brake rotor, stop using it immediately and consult the place of purchase or a distributor.
- For details on the E-THRU axle, refer to the user's manual for the E-THRU axle.
- Tires should be installed and removed by hand. If it is difficult, you can use a resin tire lever for tubeless wheels. In such cases, be sure to check the rim surface for dents, scratches, or cracks, as there is a risk of damaging the air seal between the tire and rim, which may result in air leakage. For carbon rims, check that there is no peeling or cracking of the carbon. Finally, make sure that there is no air leakage.
F12 (front 12 mm axle), R12 (rear 12 mm axle) wheel (hub axle)
- This wheel can only be used in combination with a special front fork/frame and hub axle. If it is used in combination with any other front fork/frame or hub axle, the wheel may become detached from the bicycle during riding, resulting in serious personal injury.

CAUTION
- Please note that a higher rim is more easily affected by wind, causing unstable handling.
Warm-up period
- Disc brakes have a certain warm-up period, and the braking force gradually increases along with the increasing warm-up period. Be sure to be aware of such increases. Otherwise, you may lose control of the bicycle, fall, and be seriously injured. The same situation occurs when replacing the brake pads or disc brake rotor.