Fenix E-CP power bank with lamp, black

Fenix ​​E-CP combines the function of a handheld flashlight with a power of up to 1600 lumens and a power bank with a capacity of 5000 mAh. Power is provided by a built-in Li-ion battery with a capacity of 5000 mAh, which can be recharged via a modern USB-C connector. The Luminus SST-40 light-emitting diode hidden under TIR optics can illuminate up to a distance of 222 meters and in the lowest mode will last up to 504 hours. The power bank supports fast charging protocols and can charge up to 18W (5V/2.4A, 9V/2A, 12V/1.5A).
 

Fenix ​​E-CP is a great portable EDC light and power bank in one, for recharging your mobile phone and other portable electronics. However, it also fits perfectly into your outdoor set, for example, if you are going out for a long time outside the reach of the electricity network.

All lamp parameters (luminous flux, battery operation time, waterproofing, afterglow and impact resistance) are measured in accordance with the ANSI/NEMA FL 1-2009 standard.

Parameters of the lamp with Fenix ​​E-CP power bank

• Top LED Luminus SST-40 with a lifespan of 50,000 hours.
• Six power modes: 1600 lumens (2.5 hours) -> 350 lumens (8.5 hours) -> 150 lumens (20 hours) -> 30 lumens (84 hours) -> 3 lumens ( 504 hours ) -> strobe ( 1600 lumens).
• Power is provided by a built-in Li-ion battery with a capacity of 5000 mAh.
• Recharging the battery via USB-C, charging time 2-6 hours depending on the power of the source used.
• Charging USB-C and USB-A ports for powerbank function.
• Support for fast charging protocols with a power of up to 18W for both charging and discharging (5V/2.4A, 9V/2A, 12V/1.5A).
• The lamp has a memory and turns on in the last set mode (does not apply to the highest mode and strobe).
• Backlight up to 222 meters (12400 cd).
• The back straight side of the lamp is used for standing on a mat.
• Patented intelligent overheat protection (IOP).
• Waterproof according to the IP68 standard (immersion up to 2 meters), charging port with internal protection against water ingress.
• Impact resistant to a fall from a height of 1 meter.
• Durable A6061-T6 aluminum alloy body with HA-III anodization and increased scratch resistance.
• Dimensions 138 x 28 mm.
• Weight 170 grams (including battery).
• The package includes a lamp, a wrist strap and a charging USB-C cable.
• It is possible to purchase optional accessories for the lamp, such as strap Fenix ​​ALD-05 for use of the lamp on the helmet, USB adapter for the mains, USB adapter supporting fast charging, USB adapter for the car, bicycle holder, special Fenix ​​bicycle holder or BikeBlock bicycle helmet holder and ALP-10S case.

The use

To turn the lamp on/off, press the side button for 0.5 seconds. When the light is on, simply press the side button to cycle through the modes: 3 - 30 - 150 - 350 - 1600 lumens. To switch to flash mode, hold down the side button for about 1.2 seconds.

The control button can be locked so that it does not turn on by itself, e.g. when transporting in luggage - when the light is off, press the control button twice quickly (within 0.5 seconds). To unlock, quickly press the button twice again.

Charge status indication - when the light is off, simply press the side button to start the four-part battery/power bank charge indicator hidden under the rubber cover next to the USB connectors.

Intelligent protection against overheating - if the temperature of the lamp exceeds 50 °C, the power will be automatically reduced. As soon as the temperature drops below 50 °C, it will be possible to use the highest power again.

Charging the battery/power bank - remove the back cover of the connectors and plug the attached cable into the USB-C connector on the lamp (USB-C connector - female - female), plug the other end of the cable into the computer or the USB adapter into the electrical network or the car (they are not included packaging). The indicator LED lights up red during charging and turns green when fully charged. After charging the lamp, put the connector cover back on. Charging a fully discharged battery takes about 2 hours when using an 18W source or 3.5 hours using a 5V/2A source. The lamp can be used when charging in 3, 30 and 150 lumen modes, but the charging time will be longer.

Power bank function - turn off the lamp and remove the back cover of the connectors. Plug the USB cable into one of the USB connectors (both the classic large USB-A connector and the USB-C connector work as outputs). After connecting the device to be charged, charging will start automatically, which is indicated by the four-part indicator next to the USB ports. When used as a power bank, it is also possible to light in 3, 30 and 150 lumen modes at the same time. After the process is finished, disconnect the charging device and put back the protective cover of the connectors.

Warning

• Do not disassemble the sealed parts of the lamp yourself, this will void the warranty.
• Use the control button lock when carrying the lamp in your luggage or pocket and also when storing it.

Warranty

Warranty two years.

Aftersight: 222m
Max. duration: 504 hours
Output: 100lm
Number of modes: 6
Weight: 170g
Power supply: Internal accumulator
Power supply: USB charging
Light source: Luminus SST-40
Waterproof: IP68 (immersion 2 m)