Fenix ​​WF30RE rechargeable ATEX lamp, 280 lm

Professional rechargeable lamp Fenix WF30RE with ATEX/IECex certification for use in explosive environments. The lamp is powered by a specially adapted Li-ion battery ARB-L21-2600Ex with a capacity of 2600 mAh and provides a luminous flux of up to 280 lumens with a afterglow of 170 meters. The battery is charged directly in the lamp using a special charger with safety circuits. The body of the lamp is made of aviation aluminum with high durability and impact resistance. The lamp is mainly intended for firemen and rescuers, it is also suitable as a work lamp for industrial establishments with the possibility of explosive dust and gases. These are, for example, chemical plants, refineries, textile mills, paper mills, mills, metallurgical operations, power plants and other operations.

Certificates:

• Usable in zones 1-2 of explosive gases and in zones 21-22 of explosive dust.
• Full text of certificates:
• IECEx: IECEx TUR 18.0042X:
  
  • Ex ib IIC T4 Gb
  • Ex ib IIIC T130°C Db
• ATEX: TÜV 18 ATEX 8252X:
  
  • II 2G Ex ib IIC T4 Gb
  • II 2D Ex ib IIIC T130°C Db
• It also meets CSA and NEPSI certificates.

Parameters of the ATEX work lamp WF30RE:

• A powerful Cree XP-G2 LED with a neutral shade of light with a lifespan of 50,000 hours is used.
• Four power modes: 280 lumens (6.83 hours) -> 120 lumens (15.66 hours) -> 30 lumens (120 hours) -> strobe (280 lumens).
• It uses a special Fenix ARB-L21-2600Ex Li-ion battery with a capacity of 2600 mAh. This is a modified 18650 type certified for explosive environments.
• The battery is charged directly in the lamp with the help of a special rechargeable adapter, it takes 5.5 hours to charge a completely discharged battery.
• The electronics is equipped with a protective function against too deep battery discharge, when the voltage drops below a certain limit, it automatically switches to a lower power mode.
• The lamp has a memory and can be turned on in the last set mode (not valid for the strobe).
• Indication of the state of charge of the accumulator.
• Made from aircraft hardened A6061-T6 aluminum.
• Durable hard-to-scratch surface - Type III hard anodized.
• Impact-resistant from a fall from a height of 1 meter.
• Waterproof and dustproof according to the IP68 standard (tested under water at a depth of 2 meters for 30 minutes).
• Textured aluminum reflector for a perfect light cone with an afterglow of 170 meters (7200 cd).
• Dimensions 15.05 cm (length) x 3.4 cm (head diameter) x 2.8 cm (body diameter).
• Weight 215 grams (including battery).
• The package includes: Fenix ARB-L21-2600Ex rechargeable battery, mains adapter, charging cable with safety circuits, wrist strap and spare o-ring.
• The Fenix ALD-05 strap can be purchased with the lamp to use the lamp on a helmet.

Control:

The flashlight is turned on and off by holding the button on the side for 0.5 seconds. The lighting modes can be changed by briefly pressing the button in the low-medium-high cycle.

To activate the stroboscope, turn on the light and then hold the button for 1.2 seconds. By briefly pressing the button, you will turn off the stroboscope again and the lamp will return to the last used mode.

Battery charge status indication - press the lamp button (with the lamp off). If the indicator light is green, the battery is charged to more than 85%. Green flashing means 50-85% capacity. If it lights up red, it is charged to 25-50%. Blinking red means there is less than 25% battery capacity left.

Warning of a depleted battery - the lamp will gradually automatically switch to the lowest mode and flash 3x every ten minutes.

Charging - plug the charger into the mains adapter and then into the electrical socket. The control diode on the charger flashes red and green alternately, indicating that it is possible to connect it to the lamp. Unfold the rubber cap on the lamp and connect the charger to the charging connector. The control diode on the charger lights up red during charging, and lights up green after full charge. After charging the lamp, carefully seal the charging connector again with a rubber cap. Never charge the lamp in an explosive atmosphere.

To replace the battery, unscrew the end of the lamp using an 8 mm hex key. Never replace the battery in an explosive environment.

Warning

• Carry out all servicing, charging and replacement of batteries outside of an explosive environment!
• Use only Fenix ARB-L21-2600Ex battery certified by the manufacturer.
• If the sealing rubber ring on the lamp cap thread is damaged, replace it with a spare one from the lamp package.
• If the light flickers, does not switch to higher power modes or does not light up, it may be for one of the following reasons:
  
  • The battery is dead, charge it or replace it.

Warranty

Five-year warranty for the lamp, two-year warranty for the battery.

Afterlight: 170 m
Max endurance: 120 hours
Max output: 280 lm
Weight: 215 g
Number of modes: 4
Power supply: 1x ARB-L21-2600Ex
Light source: Cree XP-G2
Waterproof: IP68 (immersion 2 m)