Black Crows Corvus Freebird 183, T12 - KH Freeride set

Corvus Freebird 183 2021/22 Set

Do you want to go your own way and don't want to compromise on driving characteristics? Then you will enjoy riding the Corvus Freebird - lightweight freeride skis - perfectly. It will allow you to go out far from the busy resorts. Even during fast, aggressive driving, you will be pleased with its stability and easy handling. A cross between freeriding and ski mountaineering, which is deceiving with its color. The Corvus model is the hardest ski with the best driving characteristics from the Freebird collection, which will satisfy even your most demanding requirements. Try it and believe it.
All the skis of the test center are serviced on professional Montana machines, so the amount of the discount reflects the time of use and cosmetic defects on the top side of the ski, the slide is structured, waxed and the skis are sharpened to a standard angle of 89 °.
Category B: Skis with small scratches on the top sheet of the ski. Tested only a few times during one winter season. After a complete service of the slide and edges.

Ideal skis for Chamonix, Verbier and Chopok

With Corvus Freebird skis, you can enjoy the longest and steepest descents, which often lead to a path through difficult terrain. 107 mm under the heel will support you even in deep snow, and you will easily change curve after curve. As a good skier, you will appreciate perfect stability at speed.

Even on hard snow, you will definitely feel it

Finishing on the slopes will no longer be a necessary evil for you, but the ideal terrain for long curves even at high speed, which will pump another dose of endorphins into your veins. You will thank the following technologies for this:

• Titanal reinforcement in the middle of the ski - dampens vibrations, gives the ski peace and grip - stability at speed.
• Carbon reinforcements along the entire length - torsional stiffness - keep the skis in the curve even on hard snow.
• Poplar core - poplar provides stability, rigidity and absorbs vibrations.
• Fiberglass reinforcement - increases torsional rigidity and protects the ski from damage - the ski has a long service life, during which it still maintains excellent driving characteristics.

Easy driving and controllability even at high speed

Black Crows skis are primarily characterized by easy handling in any snow conditions. These features are ensured by their unique cut and profile of the ski, which was created by the excellent designer Julien Regnier. In addition, Corvus Freebird skis boast:

• Front rocker - even on hard snow, the ski remains playful and floats beautifully in deep snow.
• With a gently raised heel - shortens the active edge, enables easy pivoting - you can easily and quickly change direction or stop.
• The extended toe and heel - the shortened cut gives the ski playfulness, the ski does not bite on hard ground or in soft snow and is sure to steer.
• Classic camber under the center of the ski - gives the ski stability and good edge contact with the snow - you will feel confident even in open terrain.
• Sports flex - skis allow aggressive and dynamic driving while maintaining high stability.
• With a radius of 21 m - an ideal radius for free terrain and long curves at high speeds.

Fritschi Tecton 12

The first freeride binding that combines the safety and riding properties of a downhill binding with the light weight and walking comfort of a ski mountaineering binding. Now reinforced with carbon and glass fibers.
The Fritschi Tecton 12 binding is intended for freeriders who demand uncompromising driving characteristics, high safety and low weight for ascents to virgin powder off-piste. Fritschi Tecton 12 is the first freeride spike binding with a safety tip and the stiffest downhill heel on the market. For all those who are looking for bindings for the slopes and pedaling, but do not want to compromise on factors such as safety or binding stiffness and driving characteristics.

The main advantages of the Fritschi Tecton 12 binding:

• It shuts off reliably and with Swiss precision only at the moment of fall, not when the terrain is uneven (the toe and heel of the binding can absorb shocks thanks to dynamic elasticity).
• It switches off purposefully even in walking mode - when covered by an avalanche, loss of balance during ascent or falling during short descents on tracks.
• Rigid downhill heel for perfect transmission of forces from the legs to the skis - perfect downhill properties.
• The sliding heel adapts to the bending of the ski, so you can use its full potential.
• Possibility to switch from walking mode to downhill mode without untying the shoes.
• Controlling the tying with a mallet or with a simple twist is a bonus that will make an all-day hike more enjoyable.

Pedaling and yet downhill binding

Downhill bindings are proven and their heel construction is unsurpassed, and that's where the Fritschi Tecton 12 comes from. Its rigid non-rotating heel without a joint has no backlash and enables the direct transfer of forces from the ski boot to the edge of the ski. Thus, better controllability and driving safety are achieved. Furthermore, a better transmission of forces is also achieved by means of:

• the spoon is pressed by the jaw of the heel on a large area,
• the grooves in the heel fit into the inserts on the shoe and thus increase the lateral stiffness of the binding,
• I lean the ski boot on the heel pad,
• large screw spacing,
• by attaching the heel directly to the ski,
• large and wide contact area under the toe and heel.

The heel of the binding is loaded with 4x more force than the toe when riding, which is why the Tecton 12 has a sensitive toe and a stiff (downhill) heel. Thanks to the precise transfer of the load to the edge of the ski, you will fully enjoy your ride.

Really stiff heel for a perfect riding experience

The spoon does not move even a millimeter in the heel thanks to the Power Rail grooves, which protrude from the heel and fit exactly into the grooves in the ski boot intended for the rear binding spikes. In this way, the spoon is fixed in both vertical and horizontal directions, and your every movement is transferred from the ski boot to the ski without losing energy. Thanks to this, you will be able to control the skis perfectly and have the much-needed confidence when driving. This will be appreciated not only by every good rider, but also by a beginner who is still getting used to free terrain.

Excellent skiing thanks to the active heel

The active sliding heel adapts to the ski boot by up to 10 mm when the ski bends during the ride and enables smooth bending of the ski along its entire length, which is a necessary feature of the binding for perfect skiing. A binding that does not have an active heel will prevent the ski from bending, stiffening the middle, and the ski will bend only before and behind the binding, which significantly worsens its driving characteristics. Fritschi has eliminated this problem, which is why the Tecton 12 binding is also great for all-day skiing in the resort.

The highest safety for spike bindings

The Fritschi Tecton 12 ski mountaineering binding is based on the design of a downhill binding, where the toe switches off to the sides according to the DIN switch-off force setting. Thanks to this, it shuts off precisely under rotational forces and does not cause torsional fractures. Health and safety is the main principle that the Swiss manufacturer Fritschi deals with in the development of its products. Safety is more important than weight.

Only turns binding off when you really need it

With classic spike bindings, it is easy to accidentally switch off during a descent, which can have fatal consequences on steep descents. The construction solution of both the tip and the foot of the Tecton 12 binding has a dynamic elasticity of 13 mm or 9 mm, which in other words can be imagined as clearance to absorb the forces arising from driving over bumps or sudden impacts. Even when driving vigorously on hard or heavy snow, there is no unwanted shutdown.

• The Fritschi Tecton 12 doesn't shut off too early, but only after 13mm of lateral travel at the toe and 9mm up at the heel.
• This path is sufficient to consume energy so that the binding does not switch off unintentionally after a short-term exceedance of the set tripping force DIN - in the event of a jump or bumping into an unevenness.
• The binding turns off to the side even with the toe set for walking - an important feature when buried in an avalanche, losing balance during ascent or falling on short descents on tracks.

The dynamic elasticity of the Fritschi Tecton 12 binding is the same as the downhill bindings that the Fritschi company has been producing for over 30 years and today uses this know-how in the development of skialp bindings.

Safe and lightweight freetouring binding

The weight of the equipment is also important, which is why the Fritschi Tecton 12 binding is made of carbon, glass fibers, now complemented by proven modern polymers. From design to production, everything takes place in Switzerland. Polymers reinforced with carbon and fiberglass are lighter than metal parts and at the same time have higher strength and durability. Although light weight is very important, the Fritschi brand always prioritizes safety and reliability.

Easy to turn on even on a steep slope

The new generation Fritschi Tecton 12 has an innovative designed tip that you can "kick" even blindly because it has:

• stops from below,
• stops from the sides,
• stop on the tip of the ski boot,
• sensitive trigger.

Thanks to this, when turning on the tip of the ski boot, it is precisely guided into the correct position - it is located between the spikes and a sensitive trigger, and even with a little pressure, it releases the spikes, which fit exactly into the inserts in the ski boot.

Binding properties

• Comfortable control with a mallet or with bent knees - you can comfortably switch the binding to the rising position and adjust the heel with the mallet. To switch to downhill, the binding of the Fritschi Tecton 12 can be controlled with just the stick without having to bend down to bind.
• Switching from downhill to ascent without turning off the spoon - you can comfortably switch from downhill to walking with the Tecton 12 binding by lifting the heel, when the entire heel is subsequently pushed back. You will appreciate this during ridge hikes or short passages of descent during the ascent, when it is safer to turn the heel into the downhill position with the belts.
• It does not freeze - the Fritsichi Tecton 12 ski binding is designed so that snow does not get into it, which could compress and turn into ice. Therefore, the binding works reliably in any snow and temperature.
• Adjustable binding dimensions – The heel of the binding is adjustable up to 25 mm (60 mm when using a rental mat). The binding is not compatible with "noseless" spoons TLT 7, TLT 8, DNA, PDG, Arcteryx Procline, and all that have a shank shorter than 6 mm, such as Atomic Backland (an extension is required here).
• Drilling for any skis - Fritschi Tecton 12 has easily replaceable brakes and thanks to this it is possible to drill the binding for any other skis.
• Harshajzny - the binding is compatible with Harshajznym and there is no need to switch off the binding when putting them on. The binding is also adapted to use a safety line.

All product videos and instructions.

Warranty and quality post-warranty service

For binding Fritschi Tecton 12 purchased in the Czech Republic from authorized dealers, we provide a 2-year warranty, post-warranty service and availability of parts for at least 10 years. Spare parts are in stock in Slovakia.

• Availability of spare parts for at least 10 years.

KOHLA VERTICAL Mixmohair

Durable climbing belts suitable for pedaling on the slopes and in open terrain. You will love them thanks to their versatility, ease of use and long service life. In the Universal variant - length 200 cm and attachment to any ski.
It doesn't matter whether you are pedaling on the slopes or in open terrain. With KOHLA VERTICAL Mixmohair belts you can combine both - they are really versatile. The Mixmohair type means that the climbing belts have an admixture of Nylon, which makes them very durable with great durability. Among other things, they hold perfectly and do not slip, and thanks to the new glue technology, Smart Glue, they hold perfectly on the skis. At the same time, they peel off easily. In short, climbing thousands of meters is a bit more pleasant with these belts.

• Material of rising layer: Mixmohair
• Adhesive layer material: Smart Glue
• Version: Universal
• Supplied widths: 130 mm
• Supplied for lengths: up to 200 cm
• Temperature: -30 °C
• Membrane: No, vulcanized layer - 100% waterproof
• Impregnation: Yes - fluorocarbon
• Can be trimmed for any ski: Yes
• Package includes: bag, trimming knife, Universal set for classic and twin tip foot.

Smart Glue – newly developed glue

One of the things you need with skialp belts is that the adhesive (adherent) layer holds firmly on the slide even in the most demanding conditions. The Austrian manufacturer KOHLA is a leader in adhesive layer technologies and is constantly improving and innovating them. The proof is the newly developed Smart Glue, which you can really rely on and it holds great even in really cold weather.

• When gluing ski mountaineering belts with Smart Glue glue, you do not need to use a separation film and you only need 60% of the force to unglue compared to standard belts.

Excellent slide

The climbing belts KOHLA VERTICAL Mixmohair are fast, have an excellent slide, will not slow you down in fast movement and will save the much-needed energy during a transition of several days. This is thanks to the mohair used and the method of braiding the fibers:

• mohair fibers, their cut and quality, are chosen exactly so that they are fast and have the best possible glide even on variable snow
• the fibers have a special treatment that improves the glide even more
• the use of a longer fiber significantly increases the resistance and life of the belt while maintaining a very fast slide.

It holds firmly even in spring weather

In order for the climbing belt to reliably hold on the slide, both the slide and the adhesive layer must be dry. If moisture from the snow gets on the glue, it stops working, peels off, freezes and doesn't hold. For this reason, these KOHLA VERTICAL Mixmohair climbing belts use vulcanization technology, in which the fiber is directly sealed into the bottom layer and the belt is therefore 100% waterproof. So you can enjoy your ski tour without worries, because the glue holds firmly, does not freeze and works great even in spring winters on wet snow.
Belts with vulcanized technology have a longer lifespan, because the hair is woven into the fabric and at the same time baked into the underlying rubber. Thanks to this, the belt does not get wet and has a significantly higher grip in demanding spring conditions.

Impregnated climbing belts

Good risers must hold well on the skis and glide well on the snow. Wet snow can stick to wet tracks, and there is nothing more annoying than having to drag half a kilo of snow on your leg. The belts stop sliding, it takes a lot of force unnecessarily. All KOHLA climbing belts are impregnated with fluorocarbon and snow does not stick to them.

• The impregnation repels moisture and thus prevents snow from sticking to the fibers.
• The impregnation improves the glide - climbing belts are faster and movement is easier.
• Impregnation increases the resistance of the fibers - climbing belts last longer.
• Climbing belts dry faster.
• The impregnation is environmentally friendly - without solvents and toxic substances and is biodegradable.

Still like new

With frequent use or after several seasons, the impregnation effect may decrease. In this case , you can easily renew it with KOHLA DRY CLIMB skin impregnation spray or KOHLA impregnation wax. The wax is small and convenient to have on a hike in a backpack, especially for a several-day transition.

• Video instructions for impregnation and maintenance: www.kohla.at/de/ratgeber/kohla-tv/fellpflege/

Do I attach straps to my skis?

KOHLA VERTICAL Mixmohair Universal straps can be attached to any ski - with a classic foot, for twin-tip skis or when you want to use the straps as a gift and you are not sure which straps to choose.
The tip has a steel eye T-Bar (85 mm), which is suitable for most skis, but it can be easily replaced with another attachment, e.g. for skis with a groove .
The heel of the belt is free. In the enclosed Universal set, you have everything you need to trim the straps and attach the heel exactly to your skis:

• 2 x plastic hook for twin-tip skis
• 2 x plastic hook for a normal ski heel
• 2x adjustable elastic band that you can easily attach to the belt without riveting (extends the length of the belt by up to 12 cm)
• wooden mat
• paring knife
• template for trimming

Video instructions for attaching the heel for classic and twin-tip skis: http://www.kohla.at/de/ratgeber/kohla-tv/multiclipsystem/

Will the straps fit the width and cut of my skis?

For the easiest uphill climb, it is important to have the belt cover as much of the slide as possible. Climbing strips KOHLA VERTICAL Mixmohair Universal are supplied in a width of 130 mm and a length of 190 cm. These risers can be attached to any ski, including twin-tip models.

• Video instructions for cutting belts: www.kohla.at/de/ratgeber/kohla-tv/zuschnitt-universalfelle/

Simple maintenance and service

• The belts are supplied with a bag and a cutting knife, nothing else is necessary for the belts and assembly.
• With KOHLA impregnation spray or wax, you can increase the water repellency of fibers, improve sliding properties and increase their resistance.
• In case of destruction of the attachment of the tip or the foot, the spare part can be easily replaced with a new one.
• If you destroy or lose one belt, KOHLA will make a new half pair.

Color: Pink
Safety heel: yes
Safety tip: yes
Ski length: 183.4
DIN: 5–12
Gender: Unisex
Impregnation: fluorocarbon
Carbon reinforcement: yes
Collection: 2021/22
Material: carbon
Material: fiberglass
Material: titanal
Material: Poplar
Maximum length of ski boots: unlimited
Membrane: no
Meterage: no
Setting the tripping forces: yes
pin binding: yes
Number of heels: 2
Adhesive layer: Smart Glue
Radius: 21
Fiberglass reinforcement: yes
Rising layer: Mixmohair
Belt width: 135
Titanal reinforcement: yes
Twin tip: no
Type for splitboard: no
Product type: used
Size: 183.4
Producers: Black Crows