FOX shock absorber eyelet bushing, 1/2 x 1/2"
FOX sliding sleeve for the shock absorber eye
Internal sliding sleeve for the eye of the FOX shock absorber.|
With Teflon coating (DU Bushing)
|
|
Compatible with older two-piece pivots
|
| Package contents | 1x case |
| product ID | 73937 |
•
Hello. Can you provide me with the dimensions in mm for this bushing. I need to replace the bushing on a FOX Triad shock absorber where the bushing dimensions are outer FI/inner FI/width 15.2x12.2x12.2
Automatically translated
•
Dobrý deň,
rozmery sú:
šírka: 12,7 mm
vnútorný priemer: 12,7 mm
vonkajší priemer: 15 mm
•
Hello, can I use these bushings on a 2016 Fox Float X shock? Thank you
Automatically translated
•
Dobrý deň, podľa všetkého by malo no pre istotu si skontrolujte či máte tieto rozmery : rozmery sú:
šírka: 12,7 mm
vnútorný priemer: 12,7 mm
vonkajší priemer: 15 mm
•
edit
Are these bushings original Fox? I need a Fox DHX RC4 for it.
Automatically translated
•
Hey,
Yes. I bought them and it works well not even with Fox but with RoxkShox shocks as well. This product is universal and will work well with your DHX shock.
•
Hello, the dimensions are the same as for the RockShox above in the offer, is it standardized, will it also fit for the X-Fusion O2? Can you also recommend a two-piece bolt? Thank you
All the answers to questions about delivery, payment, security, returns, warranty and much else.
We are the largest cycling e-shop in Slovakia, verified by 100,000+ customers.
We are available via e-mail, online chat, phone or in person at our MTBIKER stores.
Thanks to your order we can support cycling development.
The payment process is safe and we offer you a wide range of options.
We will reward you for your purchase and also for quality contributions in the MTBIKER forum, e-shop, trips and photo gallery.
Visit our store with a pump-track and trail access or our showroom in a historical bulding in central Bratislava.
arrow_outward
I used the bushings on a Manitou Revox Pro shock absorber and they fit. The original ones were aluminum, these are steel, so I assume they could last longer. They were pressed with a Chinese bushing press for about €5. Great job with that. And I'll add one type that I used when pressing on one side of the shock absorber. The bushing went quite hard into the shock absorber eye and after pressing and installing the pin there was a slight play in the fit between the pin and the bushing. I pressed the bushing again, gently stretched it and with a few strokes with a model needle file I increased the gap. Then the bushing was easier to press into the shock absorber eye and at the same time the play between the bushing and the pin was removed.
Automatically translated
Kvalita stále stejne dobrá...Lisovanie s príprevkom je presnejšie takže objednávam aj ten...
Translate by GoogleShow the original
Netuším prečo, ale toto púzdro mi šlo do Rockshox tlmiča ľahšie ako od Rockshox...
Translate by GoogleShow the original
Kupoval som ho do X-fusion tlmiča a sadli ako uliate, úplne ako originálne. Super.
Translate by GoogleShow the original
Po X rokoch som menil . Takže ďalších X rokov mám cil pokoj. Odporúčam!
Translate by GoogleShow the original
splnilo účel, spracovanie OK
Translate by GoogleShow the originalThe size fits, it serves its purpose.
Automatically translated
Výborne pasuje.
Translate by GoogleShow the original
Slúži na čo má
Translate by GoogleShow the original
plní funkciu
Translate by GoogleShow the original
Wszystko ok
Translate by GoogleShow the original
Tökéletes
Translate by GoogleShow the original
Funguje
Translate by GoogleShow the original
Szuper
Translate by GoogleShow the original
Pressed into the shock eye easy enough, but the bolt seemed very tight when installing on my turbo levo. Maybe it will wear in over time.
Translate by GoogleShow the originalpressed in fine, we'll see how long it lasts, the first one was worn out a long time ago so I can't judge its durability
Automatically translated
Splnilo účel
Translate by GoogleShow the originalThe bushing was damaged when pressing into the RS Super Deluxe Coil eyelet even though I used the RockShox Bushing Tool. The bushing started to deform during pressing where it is divided. This has not happened to me with other bushings, so it is possible that I received a defective piece.
Automatically translated