Fenix ​​PD35R rechargeable LED lamp

The Fenix ​​PD35R rechargeable tactical flashlight delivers a luminous flux of up to 1700 lumens (ANSI) and an afterglow of 353 meters. Excellent light performance was achieved using LED Luminus SFT-40. The lamp is powered by a Li-ion 18650 3400 mAh battery (included in the package), which is charged directly in the lamp via a modern USB-C connector. The Fenix ​​PD35R LED flashlight uses a dual tactical switch that enables faster and more reliable control in crisis situations. It can, for example , be immediately turned on directly into stroboscopic mode. The lamp head is equipped with a striking rim. Therefore, the lamp can be used to break through glass in crisis situations or for self-defense. Fenix ​​PD35R has six lighting modes that allow you to choose between high performance and long endurance, which reaches up to 100 hours. One of the lighting modes is a stroboscope with a variable frequency. The robust design and compatibility with the Fenix ​​AER-02 cable switch allows the light to be used on long weapons, so it is suitable not only for outdoor and airsoft enthusiasts, but also for professionals, armed forces and hunting.

All lamp parameters (luminous flux, battery operation time, waterproofing, afterglow and impact resistance) are measured in accordance with the ANSI/NEMA FL 1-2009 standard.

Parameters of the Fenix ​​PD35R rechargeable lamp

• A high-performance Luminus SFT-40 LED with a lifespan of 50,000 hours is used.
• Six lighting modes: Turbo 1700 lumens (2.25 hours) -> 1000 lumens (2.9 hours) -> 350 lumens (4.75 hours) -> 50 lumens (38 hours) -> 10 lumens ( 100 hours ) - Strobe 1700 lumens (strobe with variable frequency).
• Luminous flux and duration are measured with a rechargeable Fenix ​​18650 Li-ion battery with a capacity of 3400mAh ( included in the package ).
• Digitally regulated for constant brightness, intelligent protection against overheating.
• Power supply: one Li-ion 18650 battery. In an emergency, two disposable CR123A batteries can be used, but the maximum output will be limited to 1000 lumens.
• Supported supply voltage 2.85-6V, low battery warning.
• Due to the mechanical protection against polarity reversal , the positive pole of the accumulator must be exposed. Older Fenix ​​accumulators with a flat plus pole cannot therefore be used.
• Smooth parabolic reflector for a light cone with an afterglow of 353 meters (31200 cd).
• The lamp has a memory and will always turn on in the last set mode (does not apply to the strobe).
• Trapezoidal threads with increased wear resistance.
• Dimensions 13.6 cm (length) x 2.32 cm (body diameter) x 2.54 cm (head).
• Weight 140 grams (including battery).
• Made of aviation hardened aluminum, durable surface - Type III hard anodized.
• Impact-resistant from a fall from a height of 1 meter.
• Waterproof and dustproof according to the IP68 standard (tested under water at a depth of 2 meters for 30 minutes).
• Removable steel buckle.
• Hardened ultra clear glass lens with anti-reflective coating.
• Dual tactical switch at the end of the lamp (momentary on/off function).
• The flashlight comes with a wrist strap, a belt pouch, spare o-rings, a Fenix ​​18650 3400 mAh battery and a USB-C charging cable.
• As optional accessories, it is possible to purchase, for example: Fenix ​​ALD-05 strap for use of a light on a helmet, Fenix ​​AER-02 cable switch, white AOD-S V2.0 diffuser, AOT-S+ red traffic cone, ALG-00 quick-release bar mounting, Fenix ​​ALG-18 Barrel Mount, Metal Magnetic Barrel Mount, Plastic Magnetic Barrel Mount, ALG-15 Quick Release Rail Mount, Optic Light Mount, FB-1 Bike Mount, Fenix ​​Bike Mount, ALP-10S Case. For mounting on the M-LOK Fenix ​​ALG-16, due to the smaller diameter of the body, the light can only be clamped by the head or end.

Using the Fenix ​​PD35R lamp

From the factory, there may be an insulating cap inside the lamp on the battery. Remove it from the battery before first use.

To turn on/off, press the larger tactical button located at the end of the light, for immediate activation, hold the button. By pressing the secondary switch button, you can switch between power modes at any time during operation. To switch to flash mode, hold down the switch button for approximately 0.5 seconds while the light is on. Press and hold the toggle button to turn the off light directly into strobe mode.

Intelligent protection against overheating - if the temperature exceeds 60 °C, there will be an automatic reduction in performance. As soon as the temperature drops below 60 °C, it is possible to use the highest power again.

Battery charge status indication - the lamp always indicates the battery charge status three seconds after switching on. Green means a sufficient state of charge (100% - 85%), green flashing 85% - 50%, steady red light means 50% - 25% and flashing red means a critically discharged battery (25% - 1%). If the battery is discharged, the lamp will gradually automatically switch to lower power modes, in the lowest mode it will flash 3 times every five minutes.

Charging - unfold the rubber cover of the charging connector on the side of the lamp and plug in the attached cable (USB-C connector), plug the other end of the cable into the computer, or the USB adapter into the electrical network or car. The side indicator lights up red while charging. It lights up green when fully charged. Charging a fully discharged battery takes about 3 hours. The lamp cannot be used while charging.

Warning of exhausted batteries - the lamp will gradually automatically switch to the lowest mode.

Warning

• Do not disassemble the sealed parts in the lamp head yourself, this will void the warranty.
• Use only high-quality 18650 Li-ion batteries or 3V CR123A batteries to avoid damaging the lamp.
• If the protective rubber rings appear damaged after a long period of use, replace them. The rings must also be lubricated to prevent rubber erosion. By following these rules, the lamp will be properly protected against water.
• If the lamp flashes, does not switch to higher modes or does not light up, it may be for one of the following reasons:
  
  • The battery is almost empty - charge the battery or replace it.
  • The contacts inside the lamp are dirty - clean them with a cotton swab dipped in alcohol.
  • The head, body or back of the lamp is loose - add lubricant to the sealing rings and tighten both the head and the end of the lamp.

Warranty

Five-year warranty for the lamp, two years for the battery.

Output: 1700lm
Max. duration: 100 hours
Aftersight: 353m
Number of modes: 6
Weight: 140g
Power supply: 1x 18650
Power supply: 2x CR123A
Light source: Luminus SFT-40
Waterproof: IP68 (immersion 2 m)