Super B TB-1005 key for center assembly

A robust piece of iron for a few EUR. Compared to the original Shimano, it is much more practical.
When driving in any weather, a grain of sand is enough, and after a while it makes strange noises. With quality tools, cleaning the Hollowtech II is very easy and relatively quick.

Advantages of Super B TB-1005:
1.) It can be put on a large goal (or with the help of a large open-end wrench and there is also an opening where you can pass a rod, screwdriver or Allen key if there is no goal at hand. As such an improvised solution). The HT II has a fairly long thread so this is much faster.

2.) Gola holds better than the original TL-FC32, which is just a cut piece of sheet metal. That was not even possible around ergonomics.

3.) On a full-suspension bike, the rear triangle is sometimes near the Hollowtech II thread. Then with the original TL-FC32 there is only a small angle to twist and it takes an infinite amount of time. After small turns where there is a risk of knocking the paint.
TB-1005 + TL-FC25 + gola it goes comfortably. It adds a few cm and it's without hitting the frame. Gola rattles a few times and it's done.

!!! To allow the Hollowtech II threads, a TL-FC25 plastic screw is required, which fits nicely after two blows with a rubber hammer. At least this way I have it together and it won't fall out.
(The TL-FC25 can only be used on the edge even with the original Shimano TL-FC32. It's not a Super B problem, but an inaccuracy in the TL-FC25. That's why I put it there.)

I have more things from Super B, they haven't let me down yet.

Za pár EUR robustný kus železa. V porovnaní s originál Shimano to je oveľa praktickejšie.
Pri jazde za každého počasia stačí zrnko piesku a po čase stred to robí divné zvuky. S kvalitným náradím je vyčistenie Hollowtech II veľmi jednoduché a pomerne rýchle.

Výhody Super B TB-1005:
1.) Dá sa nasadiť na veľkú golu (alebo pomocou veľkého vidlicového kľúča a je tam aj otvor kde sa dá prevliecť tyčku, skrutkovač alebo imbus ak by nebola gola po ruke. Ako take improvizované riešenie). HT II má pomerne dlhý závit tak toto je oveľa rýchlejšie.

2.) Gola sa lepšie drží ako originál TL-FC32 čo je len vyrezaný kus plechu. To okolo ergonómie ani nešlo.

3.) Pri celoodpruženom biku je niekedy zadný trojuholník v blízkosti Hollowtech II závitu. Potom s original TL-FC32 je len malý uhol na krútenie a trvá to nekonečne dlho. Po malých pootočeniach kde aj hrozí oklepanie laku.
TB-1005 + TL-FC25 + gola to ide pohodlne. Pridá to pár cm a je to bez narážania do rámu. Gola pár krát zarapká a je to hotové.

!!! Na povolenie Hollowtech II závitov je potrebná plastová sranda TL-FC25, ktorá tam po dvoch ranách gumeným kladivom pekne zapadne. Takto to mám aspoň pohromade a nevypadne to.
(TL-FC25 ide nasadiť len na okraj aj pri originál Shimano TL-FC32. Nie je to problém Super B ale nepresnosť v TL-FC25. Preto som to tam naklepol.)

Mám viac vecí od Super B zatiaľ ma nesklamali.

Super nut, has a wider mounting surface around the entire perimeter of the bowl, does not tear off the grooves like this wrench, which is unusable for me: https://www.mtbiker.sk/shop/servis-a-trening/naradie/stahovaky-na-stredy/shimano-tl -fc32-key-surfaces-for-bowls-hollowtech-ii.html

Super orech, ma širšiu plochu uchytenia po celom obvode misky, nestrháva drážky ako tento pre mňa nepoužiteľný kluč: https://www.mtbiker.sk/shop/servis-a-trening/naradie/stahovaky-na-stredy/shimano-tl-fc32-kluc-plochy-na-misky-hollowtech-ii.html

Great thing for removing a heavily pulled center. A piece of iron. I put it on the stick from the gola set and made a solid putt. It wasn't a dream with a half-hearted "sticker", and especially he destroyed his teeth. I recommend it to everyone who services a bike at home.

Paradna vec na odmontovanie silno zatiahnuteho stredu. Kus zeleza. Nasadil som to na tyc z gola sady a vytvoril solidnu paku. S polovicnym "paklucom" to nebola sanca, a hlavne nicil zuby. Odporucam kazdemu, kto si servisuje doma bike.

The puller sat exactly on the center assembly, I pulled even a fairly tight center assembly without much trouble, and it left a minimal mark. With a classic key, I would certainly tear off the grooves. The puller also sits well in the ratchet.

Sťahovák sadol presne na stredové zloženie, bez väčších problémov som odtiahol aj dosť utiahnuté stredové zloženie a zanechalo to minimálny otlačok. S klasickým klúčom by som isto strhol drážky. Sťahovák sedí dobre aj v račni.

A nice massive wrench, the advantage is that you can connect a torque wrench to it, or an impact wrench when it cannot be loosened. The disadvantage, but obvious, is that you cannot release the bowl until the cranks are removed.

Fajný masívny kľúč, výhodou je, že sa dá naň napojiť momentový klúč, poprípade rázový uťahovák, keď nejde povoliť. Nevýhoda, ale zrjmá je tá, že misku nepovolíte, kým niesú kľuky preč.

The key is perfectly processed, high-quality steel, a great thing, it can be connected to a torque wrench, if someone doesn't have one, it's not a problem, it can be tightened with a fork 24

Kľúč je perfektne spracovaný kvalitná oceľ super vec možnosť pripojiť na momentový kľúč ak niekto nemá nieje to problém dá sa dotiahnuť vidlicovou 24

Great ???, I loosened and tightened the brake discs beautifully with the momentary change. I was struggling with that unlocked hand wrench. I recommend.

Skvele 👍👍👍 , momentákom som krásne uvoľnil aj dotiahol pri výmene brzdové kotúče . Tým neuzavretým ručným kľúčom som sa trápil. Odporúčam.

Excellent, fits perfectly, Better than the fork that expands over time. It just doesn't work on all centerlock nuts, it's shallow.

Výborný, sedí perfektne, Lepšie ako ten vidlicový, ktorý sa časom roztiahne. Len na všetky centerlock matice to nefunguje, je plytký.

It fits perfectly, it's small, a great alternative to wrenches, but you need another tool (wrench or a bigger ratchet)

Vyborne sedi, malicky, super alternativa ku klucovym stahovakom avsak treba k nemu dalsie naradie (kluc alebo vacsiu racnu)

better than a classic flat key, which can slip and scratch the recesses on the central assembly

lepšie ako klasický plochý kľúč, ktorý sa vie vyšmyknúť a poodierať vybrania na stredovom zložení

In addition to the center assembly, it also fits Center Lock brake nuts. The material appears cloudy.

Okrem stredového zloženia pasuje aj na Center Lock matice na brzdy. Materiál vyzerá byť zakalený.

It works great, but it didn't get scratched in the middle even when I did it over the bar.

Funguje super, ale bez skrabancov na strede sa to nezaobislo aj ked som to robil cez latku.

I use it for lefties, a class better than flat. The advantage is that a torque wrench can also be used.

Používam na lefty, o triedu lepšie ako plochý. Výhoda, že sa dá použiť aj momentový kľúč.

massive, high-quality, when the charge is folded, it cannot be used for retracting the brake disc.

masivne, kvalitne, pri zlozenom naboji nepouzitelny na zatiahnutie pre brzdovy disk.

An honest piece of iron. It is quite difficult for how small it is. So I hope it lasts a long time.

Poctivy kus zeleza. Na to ake je to male je to dost tazke. Tak dufam ze vydzri dlho.

It works fine, it seems to me that it doesn't even leave any prints on the dishes.

Funguje v poriadku, zdá sa mi že nenecháva ani žiadne odtlačky na miskách.

Massive key, replacement of the central assembly is problem-free when using it.

Masívny kľúč, výmena stredového zloženia je pri jeho použití bezproblémová.

Great for the center, too shallow for me (Vision wheels) for disc clearance.

Na stred super, na povolenie kotúča moc plytký pre mňa ( Vision kolesá).

you must have a good tool when you want to change Wednesdays (Mr.Yoda copyright)

dobry tool mat musis, ked stredy ty menit chces ( Mr.Yoda copyright )

I haven't used it yet, but things bought on MTBIKER always serve me well.

Zatial som nepouzil,ale veci kupene na MTBIKER mi vzdy dobre sluzia.