Fenix PD35 V3.0 LED lamp

The latest generation of the high-performance flashlight Fenix ​​PD35 V3.0 brings a luminous flux of up to 1700 lumens (ANSI) and an afterglow of up to 357 meters. Such a great light performance was achieved using the latest LED Luminus SFT-40. The lamp is powered by a Li-ion 18650 2600 mAh battery (included in the package) with its own charging mico-USB connector. Fenix ​​PD35 V3.0 has six lighting modes, which allow you to choose between high performance and long endurance, which reaches up to 230 hours. One of the light modes is also a stroboscope, which is suitable for crisis situations. The lamp is powered by a digitally regulated constant current to guarantee a constant light output even when the voltage in the batteries is reduced (while they are gradually discharged). It is also equipped with a battery charge indicator.

The PD35 V3.0 impresses not only with its compact size and high performance, but also with its tactical switch and the possibility of attaching the Fenix ​​AER-02 cable switch. We can therefore recommend it not only for all outdoor enthusiasts, but especially for members of the security forces and hunters.

All lamp parameters (luminous flux, battery operation time, waterproofing, afterglow and impact resistance) are measured in accordance with the ANSI/NEMA FL 1-2009 standard.

Fenix ​​PD35 V3.0 lamp parameters

• A high-performance Luminus SFT-40 LED with a lifespan of 50,000 hours is used.
• Six lighting modes: Turbo 1700 lumens (1.5 hours) -> 600 lumens (2.5 hours) -> 150 lumens (8.5 hours) -> 50 lumens (26.5 hours) -> 5 lumens ( 230 hours ) - Strobe 1700 lumens (strobe with variable frequency).
• Luminous flux and duration are measured with a rechargeable Fenix ​​18650 Li-ion battery with a capacity of 2600mAh ( included in the package ).
• Digitally regulated for constant brightness, intelligent protection against overheating.
• Power supply: one Li-ion 18650 battery or two disposable CR123A batteries.
• Supported supply voltage 2.8-6.4V, low battery warning.
• Due to the mechanical protection against polarity reversal , the positive pole of the accumulator must be exposed. Older Fenix ​​accumulators with a flat plus pole cannot therefore be used.
• Smooth parabolic reflector for a light cone with an afterglow of 357 meters (31900 cd).
• The lamp has a memory and will always turn on in the last set mode (does not apply to the strobe).
• The LED indicator in the side button always shows the battery charge status when the light is turned on (calibrated for the use of 18650 Li-ion batteries).
• Trapezoidal threads with increased wear resistance.
• Dimensions 13.4 cm (length) x 2.28 cm (body diameter) x 2.54 cm (head).
• Weight 83.5 grams (without battery) or 133.5 grams (including battery).
• Made of aviation hardened aluminum, durable surface - Type III hard anodized.
• Impact-resistant from a fall from a height of 1 meter.
• Significant surface grooves for better grip, the design prevents the lamp from rotating on an uneven surface.
• Waterproof and dustproof according to the IP68 standard (tested under water at a depth of 2 meters for 30 minutes).
• Removable steel buckle.
• Hardened ultra clear glass lens with anti-reflective coating.
• Tactical switch at the end of the light (momentary on / off function).
• The lamp comes with a wrist strap, belt pouch, spare o-rings, Fenix ​​18650 2600 mAh battery with USB and micro USB charging cable.
• As optional accessories, it is possible to purchase, for example: Fenix ​​ALD-05 strap for use of the light on the helmet, Fenix ​​AER-02 cable switch, AOD-S diffuser, AOF-S+ red filter, AOF-S+ green filter, AOF-S+ blue filter, holder for bicycle, Fenix ​​ALB-10 bicycle holder or bike helmet lamp holder BikeBlock, ALG-15 quick-release gun rail mount, Fenix ​​ALG-00 quick-release mount, metal magnetic mount, ALP-10S case. For mounting on the M-LOK Fenix ​​ALG-16, due to the smaller diameter of the body, the light can only be clamped by the head or end.

The use

From the factory, there may be a black insulating cap inside the lamp on the battery. Before first use , remove it from the battery.

To turn it on, press the switch located at the end of the lamp, for immediate activation, gently hold the button. By pressing the side button near the head of the lamp, you can cyclically switch between five permanent lighting modes at any time during operation. To switch to strobe mode, hold down the side button for about 0.5 seconds.

Intelligent protection against overheating - if the temperature of the lamp rises above 60 °C, it will automatically reduce the power in gradual steps until its temperature stabilizes. As soon as the temperature of the lamp drops below 60 °C, the power will automatically increase again to the original level.

Indication of the state of charge of the batteries - each time it is switched on, the indicator LED in the side button of the lamp is activated for three seconds. If the indicator light is green, the battery is charged to more than 85%. Green flashing means 50-85% capacity. If it lights up red, it is charged to 25-50%. Red flashing means less than 25% battery capacity left (only works when using 18650 Li-ion battery).

Warning of discharged batteries - the lamp will gradually automatically switch to the lowest mode, in the lowest mode, the indicator LED in the button will flash red three times every 10 minutes. This indicates the need to charge the battery or replace it with a fully charged one.

Charging - plug the USB cable into the side micro-USB connector on the battery, the light on the top of the battery lights up red during charging. When fully charged, it lights up green or blue. The charging time of a fully discharged battery is 3-3.5 hours.

Warning

• Do not disassemble the sealed parts in the lamp head yourself, this will void the warranty.
• Use only high-quality 18650 Li-ion batteries or 3V CR123A batteries to avoid damaging the lamp.
• If the protective rubber rings appear damaged after a long period of use, replace them. The rings must also be lubricated to prevent rubber erosion. By following these rules, the lamp will be properly protected against water.
• If the light flickers, does not switch to higher power modes, or does not light up, it may be for one of the following reasons:
  
  • The batteries are almost empty - charge the battery or replace it.
  • The contacts inside the lamp are clogged - clean them with a cloth soaked in alcohol.
  • The head, body or back of the lamp is loose - add lubricant to the sealing rings and tighten the head and the end of the lamp.

Five-year warranty for the lamp, two years for the battery.

Output: 1700lm
Max. durability: 230 hours
Aftersight: 357m
Number of modes: 6
Weight: 83.5g
Power supply: 2x CR123A
Power supply: 1x 18650
Light source: Luminus SFT-40
Waterproof: IP68 (immersion 2 m)