Fenix WF11E ATEX flashlight

Professional flashlight Fenix WF11E with ATEX/IEC certification for use in explosive environments. The flashlight is powered by three AA batteries and provides a light output of up to 200 lumens. The flashlight body is made of antistatic plastic (polycarbonate RTP399 x 133887) with high durability and impact resistance. Additionally, the flashlight is equipped with a sturdy clip with an integrated magnet and a magnetic tail cap, so it can be attached to any iron surface. The flashlight is intended primarily for firefighters and rescuers, and is also suitable as a work light for industrial operations such as chemical plants, refineries, textile mills, paper mills, mills, and other operations with an increased risk of explosive gases and dust.

Certificates:

• Usable in zones 0-2 for explosive gases and zones 20-22 for explosive dust.

• Full text of certificates:
  - IECEx: Ex ia IIC T4 Ga / Ex ia IIIC T130 ° C Da IP66 / IP67
  - ATEX: II 1G Ex ia IIC T4 Ga / II 1D Ex ia IIIC T130 °C Da IP66 / IP67

• Also includes CSA and PCEC certificates.

Parameters of Fenix WF11E ATEX flashlight:

• A powerful Cree XP-G2 LED with a warmer light tone and a lifespan of 50,000 hours is used.

• Three power modes: 200 lumens (10 hours) -> 100 lumens (29.5 hours) -> 30 lumens (70 hours).

• Uses three AA batteries. Fenix strongly recommends using only battery types certified by the manufacturer: ENERGIZER E91, DURACELL MN1500, and RAYOVAC 815

• Protection against accidental reverse battery insertion (polarity reversal).

• Made of solid antistatic plastic (polycarbonate RTP399 X 133887).

• Knurled surface for better grip.

• Sturdy clip with integrated magnet.

• Magnetic tail cap.

• Dustproof and waterproof according to IP67 standard, submersible up to 1 meter underwater.

• Smooth aluminum reflector for a perfect beam with a range of over 185 meters (8512 cd).

• Dimensions 16.75 cm (length) x 4.9 cm (head diameter) x 2.4 cm (body width).

• Weight 160 grams (without batteries).

• The package includes three Energizer alkaline AA batteries approved for use in the flashlight, a spare o-ring, a lanyard, and a certificate valid for the EU.

Usage:

The flashlight is turned on and off by holding the side button for 0.5 seconds. Lighting modes can be changed by short presses of the button in the order low-medium-high.

To replace batteries, unscrew the flashlight head and remove the battery holder. When replacing batteries, pay attention to the correct polarity indicated on the holder. Insert the holder back and screw on the flashlight head.

Warning

• Perform all service interventions and battery replacements outside of the explosive environment!

• In explosive environments, use only batteries certified by the manufacturer: ENERGIZER E91, DURACELL MN1500, and RAYOVAC 815

• Never mix batteries from different manufacturers, of different ages, or with different levels of discharge.

• For long-term storage, we recommend removing the batteries from the flashlight to prevent potential leakage and damage to the flashlight.

• If the protective rubber rings appear damaged after prolonged use, replace them.

• If the flashlight blinks, does not switch to higher power modes, or does not turn on, it may be due to one of the following reasons:

  • Batteries are nearly depleted - replace them.

  • Contacts inside the flashlight are dirty - clean them with a cotton swab dipped in alcohol.

  • The flashlight body is loose, tighten it.

Warranty

Five-year warranty.

Max output:200lm
Max runtime:70h
Beam distance:185m
Number of modes:3
Weight:160g
Power supply:3x AA
Light source:Cree XP-G2
Water resistance:IP67 (1m submersion)