Shimano Deore E-M6220 hydraulic rear brake, Post Mount, hose 1,700 mm + pads D03S

WARNING
Information on the installation, adjustment, and replacement of products not found in the user's manual can be obtained at the place of purchase or from a distributor. A dealer's manual intended for professional and experienced bicycle mechanics can be found on our website (https://si.shimano.com).
For safety, thoroughly read this "user's manual" before use, follow it for proper use, and store it for future reference.
The following instructions must always be observed to prevent personal injury and physical damage to equipment and surroundings. Instructions are classified according to the degree of danger or damage that may occur in case of improper use of the product.
DANGER - Failure to follow instructions will result in death or serious injury.
WARNING - Failure to follow instructions could result in death or serious injury.
CAUTION - Failure to follow instructions could result in personal injury or physical damage to equipment and surroundings.

WARNING
- Because each bicycle may handle slightly differently depending on the model, learn the correct braking technique (including brake lever pressure and bicycle handling characteristics) and operation of your bicycle.
- Improper use of the bicycle's braking system can result in loss of control, which may lead to serious injury due to a fall or collision.
- Do not disassemble or modify the product. This may cause the product to malfunction, you may fall unexpectedly and be seriously injured.
- Downhill cycling and freeride are inherently dangerous activities. It is strongly recommended that riders use head and body protection and perform thorough safety checks of their bicycles before riding. Remember that you ride at your own risk and therefore you should carefully consider your experience and abilities. There is a risk of being involved in an accident resulting in serious injury or even death.
- Before riding, riders must get used to the higher performance of this brake.
- The braking system is designed for downhill cycling and freeride, and its braking force is much higher than that of other brakes. If you ride a bicycle without being sufficiently familiar with the braking characteristics, you may be involved in an accident that could result in serious injury or even death. In addition, brake settings do not allow for riding in city streets.
- Sudden braking can cause the bicycle to fall forward, which can result in serious injury or even death.
- 220 mm, 203 mm, and 180 mm rotors provide greater braking force than 160 mm rotors. If you ride a bicycle without thoroughly familiarizing yourself with the braking characteristics, braking may result in a fall from the bicycle with possible serious injury or fatal accident.
- Keep fingers away from the rotating rotor. The rotor is sharp enough to cause serious finger injury if caught.
- Do not touch the calipers or rotor while riding or immediately after dismounting the bicycle. During braking, the calipers and rotor heat up, so touching them can cause burns.
- Do not allow oil or grease to get on the rotor or pads. Riding a bicycle with oil or grease on the rotor or pads can cause the brakes to malfunction and lead to serious injury due to a fall or collision.
- Check the pad thickness and do not use them if they are 0.5 mm thick or less. This can cause the brakes to malfunction and lead to serious injury due to a fall or collision.
- Do not use the rotor if it is cracked or deformed. The rotor may break and lead to serious injury due to a fall.
- Do not use the rotor if its thickness is 1.5 mm or less. Also, do not use it if the aluminum surface is visible. The rotor may break and lead to serious injury due to a fall.
- Do not apply the brakes continuously. This can cause a sudden increase in brake lever engagement, cause the brakes to malfunction, and lead to serious injury due to a fall or collision.
- Check the information on supported models for each oil type and use the correct oil for the product. Failure to do so may cause the brakes to malfunction and lead to serious injury.
- For more information, visit https://si.shimano.com/dm/BROIL
- Do not mix SHIMANO hydraulic mineral oil with SHIMANO low-viscosity oil. This can cause the brakes to malfunction and lead to serious injury.
- Do not use the brakes if there is a fluid leak. This can cause the brakes to malfunction and lead to serious injury due to a fall or collision.
- Do not apply the front brake too strongly. If you do, the front wheel may lock up and the bicycle may flip forward, causing serious injury.
- Because the required braking distance will be longer in wet weather, reduce your speed. Apply the brakes early and gently. Otherwise, serious injury due to a fall or impact may occur.
- Wet road surfaces can cause tires to lose traction. To prevent this, reduce your speed and apply the brakes early and gently. If tires lose traction, you may fall and be seriously injured.
Warnings regarding SHIMANO low-viscosity oil
- If SHIMANO low-viscosity oil gets into your eyes, rinse them with clean water and seek medical attention immediately. Eye contact can cause irritation.
- If SHIMANO low-viscosity oil comes into contact with your skin, wash it thoroughly with soap and water. Skin contact can cause rashes and discomfort.
- When using SHIMANO low-viscosity oil, protect your nose and mouth with a protective respiratory mask and ensure the area is well ventilated. Inhaling vapor or fumes emitted from SHIMANO low-viscosity oil can cause nausea.
- After inhaling vapors or fumes emitted from SHIMANO low-viscosity oil, immediately move to a place with fresh air. Cover yourself with a blanket. Stay warm in a stable position and seek professional medical attention.
Warm-up period
- Disc brakes have a certain warm-up period, and braking force gradually increases with the warm-up period. Accidents or falls due to loss of control of the bicycle may occur, which can result in serious injury. The same situation will occur when replacing pads or the rotor.