Fenix E20 V2.0 LED lamp

The latest generation of the Fenix ​​E20 V2.0 LED lamp offers a high luminous flux of up to 350 lumens (ANSI) and an afterglow of up to 126 meters. This version offers simple control and four levels of light output with an operating time of up to 200 hours. Control and switching on is handled by the end button. It uses two commonly available pencil batteries for power supply, of course disposable and rechargeable batteries can be used. A unique innovation is a special collimator that creates a light cone with an afterglow of 126 meters. The collimator is made with technology used in the automotive industry and its height is only 3 millimeters, which is less than half compared to commonly used optics. Thanks to the length of only 127 millimeters and the weight of 42 grams (without batteries), it can be carried with you at all times. This lamp is an ideal lighting tool with an excellent ratio of high performance, quality and price.

All lamp parameters (luminous flux, battery operation time, waterproofing, afterglow and impact resistance) are measured in accordance with the ANSI/NEMA FL 1-2009 standard.

The lamp Fenix ​​E20 V2.0 replaces the older models Fenix ​​L2T V2.0, Fenix ​​E20 and Fenix ​​E21.

Fenix ​​E20 V2.0 lamp parameters

• A modern Luminus SST-20 LED with a lifespan of 50,000 hours is used.
• Four performance modes:
  
  • measured with 1900mAh rechargeable NiMH battery: 350 lumens: (1.5 hours) -> 150 lumens (5.5 hours) -> 30 lumens (34.5 hours) -> 5 lumens (140 hours)
  • measured with included alkaline batteries: 350 lumens (3.75 hours) -> 150 lumens (11.25 hours) -> 30 lumens (93.5 hours) -> 5 lumens (200 hours)
• It uses two pencil batteries (type AA - alkaline, lithium or rechargeable NiMH). These batteries are cheap and widely available.
• Energizer L91 Ultimate Lithium lithium pencil batteries (especially suitable for extreme conditions and expeditions) will provide the longest duration.
• Protection against accidental insertion of batteries in reverse (reverse polarity).
• Intelligent protection against overheating.
• Electronics with digital constant power regulation and protection against reverse battery insertion.
• Made of aircraft-grade hardened aluminum type T6, the lamp is impact-resistant when dropped from a height of 1 meter.
• Durable surface - Type III hard anodized.
• Prominent grooved surface for better grip.
• Fixed clip for safe and easy carrying of the lamp (removable).
• A special super-thin collimator only 3 mm high, made with technology used in the automotive industry.
• Afterlight of 126 meters (3950 cd).
• Waterproof and dustproof according to the IP68 standard (tested under water at a depth of 2 meters).
• Dimensions 12.7 cm (length) x 1.68 cm (body diameter) x 2.1 cm (head diameter).
• Weight 42 grams (without batteries).
• The flashlight comes with a wrist strap, a spare o-ring and two alkaline batteries.
• As optional original accessories, it is possible to purchase: diffuser AOD-S, red filter AOF-S, swivel belt case AB02, Fenix ​​bicycle holder, strap for using the lamp as a headlamp or ALP-MT case.
• LockBlocks bicycle holder, BikeBlock bicycle helmet holder are also compatible with the lamp.

 Use of Fenix ​​E20 V2.0 LED lamp

To turn it on, press the switch located at the end of the lamp. The lamp is always switched on in the lowest mode. When the lamp is on, you can change the power modes at any time by gently pressing the button (they switch cyclically low - medium - high - turbo).

Intelligent protection against overheating - if the temperature of the lamp rises above 58°C, it will automatically reduce the power in gradual steps of 1% every second until the power is reduced to 150 lumens. As soon as the temperature of the lamp drops below 58°C, the power will automatically increase again to the original level. Operation at the highest power mode is thus not limited by time, but only by temperature.

Warning about dead batteries - if the battery voltage drops below the set level, the lamp will automatically reduce power. When the batteries are dead, only the lowest power mode will be available.

Warning

• Do not disassemble the sealed part in the lamp head yourself, this will void the warranty.
• Remove the batteries from the lamp if they are dead. Especially with disposable batteries, there is a risk of them leaking and subsequently damaging the lamp.
• If the protective rubber rings appear damaged after a long period of use, replace them. The rings must also be lubricated to prevent rubber erosion. By following these rules, the lamp will be properly protected against water.
• If the light flickers, does not switch to higher power modes, or does not light up, it may be for one of the following reasons:
  
  • Batteries are almost empty - replace them.
  • The contacts inside the lamp are clogged - clean them with a cotton swab dipped in alcohol.
  • The back of the lamp is loose - add lubricant to the sealing rings and tighten.

Max power: 350lm
Max endurance: 200 hours
Aftersight: 126m
Number of modes: 4
Weight: 42g
Power supply: 2x AA
Light source: Luminus SST-20
Waterproof: IP68 (immersion 2 m)